Heat source equipment direct fired hot blast stove

Specifications

hot blast stove
1.High efficiency
2.Environmental proyection
3.High performance
4.Professional manufacturer

Heat source equipment direct fired hot blast stove

 

Introduction of pellet hot-blast stove:

 

Direct-fired hot-blast stove is made up of combustion chamber, settling chamber and mixing air chamber. Fuel is put into the combustion chamber manually. Under the effect of air blower, the fuel burns fiercely and produces high-temperature smoke with dust, which enters into the settling chamber to remove dust. Certain amount of cold air can mix with the hot air from the clean room, so hot smoke of different temperature can be offered. It can offer heat source for various kinds of drying systems.

 

 

 

 

Advantage of pellet hot-blast stove:

 

1) the coal types of wide adaptability;
2) high combustion efficiency, thermal efficiency > 95%, if the quantity of heating fuel consumption such as the table;
3) output stable heat load, mechanical combustion, simple operation, adjustment is very convenient;
4) environmental protection standards, no secondary pollution, the operating environment is clean;
5) hot air spotlessness, dustiness 30 ~ 120 mg/Nm3;
6) convenient adjustment, hot air temperature below 1000 °C, + / - 5 °C continuous heating wind temperature stability;
7) equipment strong durability, low operating cost, simple maintenance.

 

 

 

 

Range of application:

 

Cleaning: detergent, the 4 a zeolite, the layered sodium silicate, detergent additives, etc

Ceramic: ceramic powder, glaze, clay, kaolin, etc

Fertilizer: compound fertilizer, monoammonium phosphate, diammonium phosphate, potassium chloride, magnesium sulfate, potassium sulfate, etc

Chemical categories: quartz sand, alumina, polyaluminium chloride, chemical additives, water purifier, ferric sulfate, etc

Building materials: ceramic fiber, insulation board, heat preservation cotton, ultrafine powder, gypsum, quartz sand, etc

Environmental protection: the sludge drying, papermaking black liquor and pharmaceutical waste liquid treatment, lignin, etc

The other: coal, wood drying, lees, food, feed, acetylene cylinder, rubber, silicone, paper plastic mould, dyes, etc

 

 

 

 

Parameters of pellet hot-blast stove:

 

 

Model	Heat Supply (kcal/h)	Burning Area (Length*Width)	Heating efficiency	Coal Consumption (standard coal)
HJ-20	20*104	0.6*0.7m2	≥90%	30 kg/h
HJ-40	40*104	0.8*1.0 m2	≥90%	50 kg/h
HJ-60	60*104	0.8*1.2 m2	≥92%	70 kg/h
HJ-100	100*104	1.0*1.4 m2	≥92%	100 kg/h
HJ-150	150*104	1.0*1.8 m2	≥92%	150 kg/h
HJ-200	200*104	1.2*2.0 m2	≥92%	300 kg/h
HJ-250	250*104	1.2*2.2 m2	≥92%	400 kg/h
Remarks	Besides the above models, we can also supply special model as your request.

 

 

 Certification:

 

 

 

 

Hengjia supply kinds of heat  source series equipment such as direct-fired hot-blast stove,coal-fired hot air funace,HLF type vertical hot-blst stove,steelwork tubulation heat exchanger,indirect heating stove,eletric heating stove,fuel gas stove,pulverized cola injection machine,rotary rype pulverized coal burner,biomass burner,coal gasifier

 

 

 

 

 

 

Produktgruppe : Heizung Herd-Ausrüstung > Holz und Kohle brennt Herd